Grazioli MV6 High Power Multiband Vertical 20-6 Meters Ground Plane 3KW

Home
Everything Antenna
Vertical Antenna
Grazioli MV6 High Power Multiband Vertical 20-6 Meters Ground Plane 3KW

Home
Everything Antenna
Amateur Base
HF
Grazioli Italian HF Antennas
Grazioli MV6 High Power Multiband Vertical 20-6 Meters Ground Plane 3KW

Grazioli MV6 High Power Multiband Vertical 20-6 Meters Ground Plane 3KW

Price:

$689.00

SKU:

MV6

Brand:

Grazioli

Shipping:

Calculated at checkout

Product Description

Grazioli MV6 High Power Multiband Vertical 20-6 Meters Ground Plane

No Traps, No Coils, No Moving Parts, No Additional radials required.

This is the Ferrari of upper HF band verticals

Free Lower 48 Ship!

Overview

Vertical multiband 1/4 λ Ground Plane base-fed antenna

HF 20, 17, 15, 12, 10m + VHF 6m

Fed at the base

Max Input Power: 3 kW

Total Height: 22.14 FT

Antenna weight: 17.2 LBS

Main Features

Grazioli MV6

Now supplied with original FAIR-RITE FT240-43 ferrite toroid Made in USA

Vertical multiband 1/4 λ Ground Plane base-fed antenna for the following HAM bands: 20, 17, 15 12, 10 and 6m.

Extremely robust construction in AW6063-T66 aluminum alloy and CNC machined parts from solid stock.

Supplied with high-quality 304 and 316 stainless steel fasteners for long rust-free operating life.

High input power, up to 3 kW continuous All-mode.

Detailed assembly manual and serial number that identifies the production batch and construction data.

Materials and Construction

For our tubing, we used the best material that can be used for antenna construction; it is the Aluminum, Magnesium and Silicon alloy named AW6063-T66, hardened to the T-66 state. It gives the stylus exceptional strength, which is made by extrusion and then cold-drawn.

Of extremely robust construction, the central stylus uses 42x2mm diameter tubes at the base and 19x1.25mm diameter at the tip, while the side stubs and ground plane radials are made of 13 and 10mm diameter telescopic tubes;

The ground plane is formed by 4 horizontal radials of approximately 2.7m in length, and the vertical stubs are held in place by 3 crossbars, the first connected to the base of the stylus is made of CNC-machined rectangular-section aluminium tubing, and the other 2 of thermoplastic material, one with 4 arms in the middle part, and one with 2 arms in the upper part.

All hardware is made of stainless steel, the tubes are secured with robust, quality stainless steel AISl-316 clamps, brackets, hardware, and U-bolt and V-bolt U-bolts are made of AISl-304 stainless steel.

Technical Data

SWR and Smith Chart

Technical choices that make the difference

A high-performance and robust antenna with Grazioli brand standards.

The basic idea was to make an efficient antenna, without using traps that reduce efficiency, and without using impedance transformers that limit the applicable power.
Based on these assumptions, we realized MV6, which by using resonant elements parallel (stubs) to the central stylus, allowed us to realise an efficient antenna on all bands covered.

A high-performance multiband

The stylus consists of a central radiator for the lower 20m band flanked by 4 side stubs resonating on the higher 17,15,12,10 + VHF 6m bands. The side stubs are 1/4 wavelength without traps that would reduce their efficiency. The antenna is fed directly without the use of impedance adapters or transformers, which would introduce losses and limit the applicable power, and is equipped with a high-impedance inductance that creates a DC short circuit, grounding any disturbances caused by atmospheric events and/or electrostatic discharges.
Calibration is done by adjusting the telescoping parts of the stubs and the central stylus, each frequency is independent and does not affect the other bands, except for the 17m band, which also determines the resonance of the 6m band: We recommend the use of a graphic antenna analyser such as Rig-Expert or Nano VNA, which makes calibration much easier.

NOTE:
If used in very windy areas, bracing with non-conductive cables using the supplied fifth wheel is recommended.
We recommend the use of a CHOKE (not supplied) to be installed immediately below the connector to avoid possible RF feedback on the coax

The RF Choke for attenuating common mode currents

Now supplied with the MV6 is an original FAIR-RITE Made in the USA FT240-43 ferrite toroid for “Home Made” construction of your high-performance Choke. This arrangement allows you to significantly attenuate common mode currents in the HF band (1.8-30MHz), which could reduce the performance of your antenna.

Material not supplied at customer's expense for fabrication:
- No.2 PL259 connectors suitable for the type of cable you intend to use.
- (1 PL259 + 1 SO239 in case of using plastic protection box).
- Approximately 1.2m of good quality coaxial cable, such as RG58 for continuous powers up to 300 Watt AWG @ 30MHz, or RG142BU in Teflon for continuous powers up to 1500 Watt AWG @ 30MHz.

We absolutely discourage the use of cables with FOAM foam-type dielectric (white spongy dielectric) because they cannot be wrapped around the toroid without compromising its electrical characteristics.

UHF Connector

The FE10V connector is not a commercial SO-239 type connector as most manufacturers use. The connector was designed and built directly by us, has a real impedance of 50 Ohms and can be used up to 500 MHz. The goal was to create a reliable connector capable of withstanding 5kW CW continuous at 30 MHz.

The body is made of CW614N nickel-plated brass, while the pin is plated in 24K gold to avoid oxidation and equipped with a 4-fin insulator that maintains its centering and elasticity, avoiding contact losses.

The insulating part is made of PTFE which is one of the best insulating materials due to its exceptional electrical (low dielectric constant, and reduced loss factor) and thermal (operating temperature from -100 ° to + 260 °) and is protected from a special elastomer hood that prevents water and humidity infiltration

The Mounting Bracket

Made of 2.5mm thick AISI304 stainless steel, it is fixed to the antenna tube by means of a clamp closure system, creating an extremely strong mechanical locking.

Fixing to the mast is made with AISI304 M6 V-Bolt and high type nuts to facilitate tightening.

Distributed by 59signal.com